- 您现在的位置：买卖IC网 > Sheet目录1194 > ADT7476EBZEVB (ON Semiconductor)BOARD EVALUATION FOR ADT7476
ADT7476
Table 82. REGISTER 0X78 ? CONFIGURATION REGISTER 3 (POWER-ON DEFAULT = 0X00) (Note 1)
Bit No.
[0]
[1]
Mnemonic
ALERT
THERM/
2.5V
R/W
R/W
R/W
Description
ALERT = 1, Pin 10 (PWM2/SMBALERT) is configured as an SMBALERT interrupt output to
indicat e out-of-limit error conditions.
ALERT = 0, Pin 10 (PWM2/SMBALERT) is configured as the PWM2 output.
THERM = 1 enables THERM functionality on Pin 22 and Pin 14, if Pin 14 is configured as
THERM, determined by Bits 0 and 1 (PIN14FUNC) of Configuration Register 4. When THERM
is asserted, if the fans are running and the BOOST bit is set, then the fans run at full speed.
Alternatively, THERM can be programmed so that a timer is triggered to time how long THERM
has been asserted.
THERM = 0 enables 2.5 V measurement on Pin 22 and disables THERM. If Bits [5:7] of
Configuration Register 5 are set, THERM is bidirectional. If they are 0, THERM is a timer input
only.
Pin 14 FUNC
00
01
10
11
00
01
10
11
THERM/2.5 V
0
0
0
0
1
1
1
1
Pin 22
+2.5 V IN
+2.5 V IN
+2.5 V IN
+2.5 V I N
THERM
+2.5 V I N
THERM
THERM
Pin 14
TACH4
THERM
SMBALERT
GPIO6
TACH4
THERM
SMBALERT
GPIO6
[2]
[3]
[4]
[5]
[6]
[7]
BOOST
FAST
DC1
DC2
DC3
DC4
R/W
R/W
R/W
R/W
R/W
R/W
When THERM is an input and BOOST = 1, assertion of THERM causes all fans to run at the
maximum programmed duty cycle for fail-safe cooling.
FAST = 1 enables fast TACH measurements on all channels. This increases the TACH
measurement rate from once per second to once every 250 ms (4x).
DC1 = 1 enables TACH measurements to be continuously made on TACH1. Fans must be
driven by dc. Setting this bit prevents pulse stretching because it is not required for dc driven
motors.
DC2 = 1 enables TACH measurements to be continuously made on TACH2. Fans must be
driven by dc. Setting this bit prevents pulse stretching because it is not required for dc driven
motors.
DC3 = 1 enables TACH measurements to be continuously made on TACH3. Fans must be
driven by dc. Setting this bit prevents pulse stretching because it is not required for dc driven
motors.
DC4 = 1 enables TACH measurements to be continuously made on TACH4. Fans must be
driven by dc. Setting this bit prevents pulse stretching because it is not required for dc driven
motors.
1. This register become read-only when the Configuration Register 1 Lock bit is set to 1. Any further attempts to write to to this register have no
effect.
Table 83. REGISTER 0X79 ? THERM TIMER STATUS REGISTER (POWER-ON DEFAULT = 0X00)
Bit No.
[7:1]
[0]
Mnemonic
TMR
ASRT/
TMR0
R/W
Read-only
Read-only
Description
Times how long THERM input is asserted. These seven bits read 0 until the THERM
assertion time exceeds 45.52 ms.
This bit is set high on the assertion of the THERM input and is cleared on read. If the THERM
assertion time exceeds 45.52 ms, this bit is set and becomes the LSB of the 8-bit TMR
reading. This allows THERM assertion times from 45.52 ms to 5.82 sec to be reported back
with a resolution of 22.76 ms.
Table 84. REGISTER 0X7A ? THERM TIMER LIMIT REGISTER (POWER-ON DEFAULT = 0X00)
Bit No.
[7:0]
Mnemonic
LIMT
R/W
R/W
Description
Sets maximum THERM assertion length allowed before an interrupt is generated. This is an
8-bit limit with a resolution of 22.76 ms allowing THERM assertion limits of 45.52 ms to
5.82 sec to be programmed. If the THERM assertion time exceeds this limit, Bit 5 (F4P) of
Interrupt Status Register 2 (0x42) is set. If the limit value is 0x00, an interrupt is generated
immediately on the assertion of the THERM input.
http://onsemi.com
62
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ADT7490ZEVB
BOARD EVALUATION FOR ADT7490
ADZS-21262-1-EZEXT
BOARD DAUGHTER FOR ADSP-21262
ADZS-BF-EZEXT-1
BOARD DAUGHTER ADSP-BF533/561KIT
ADZS-BFAV-EZEXT
BOARD DAUGHT ADSP-BF533,37,61KIT
ADZS-BFSHUSB-EZEXT
BOARD DAUGHTER EZ EXTENDER
ADZS-BRKOUT-EX3
ADZS-BRKOUT-EX3
ADZS-SHAUDIO-EZEXT
SHARC AUDIO EZ-EXTENDER
ADZS-WVGALCD-EX3
BOARD EXTENDER WVGA/LCD EI3
相关代理商/技术参数
ADT7481
制造商:AD 制造商全称:Analog Devices 功能描述:Dual Channel Temperature Sensor and Over Temperature Alarm
ADT7481ARMZ
功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
ADT7481ARMZ-001
功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
ADT7481ARMZ-1
功能描述:IC SENSOR TEMP 2CH ALARM 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6
ADT7481ARMZ-1R7
功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
ADT7481ARMZ-1REEL
制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
ADT7481ARMZ-1REEL7
制造商:AD 制造商全称:Analog Devices 功能描述:Dual Channel Temperature Sensor and Over Temperature Alarm
ADT7481ARMZ-1RL
功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor